Author Topic: All kinds of cab work  (Read 64 times)

Offline Howard Bullit Stubbs

  • Rookie
  • *
  • Posts: 8
All kinds of cab work
« on: April 09, 2017, 09:41:52 AM »
 Lots of work going on in and around the cab, mostly mechanical. Removed non-op AC, new valve cover gaskets and fabricating new heat shields.
 Gone - AC compressor and all related equipment, including condenser in front of radiator. Removed mounting bracket from the front side of AC compressor and put it back on the engine in order to mount an idler pulley for the alternator belts. Ordered a Dayco 89056 Idler pulley, which is used on 1989-1992 dodge ram P.U. with a 360 cu. in. engine, non- AC. I'll have to make a short bracket for this which will then bolt on to AC mounting bracket.
 Heat shields are going to bolt on to the valve covers at the lower 4 bolts. I'm going to line them with exhaust header heat wrap. Then we  will apply new heat barrier insulation to the engine cover.
 Have to remove a section of floor under drivers seat and weld in a new section. I wish I could find NOS floor pan and just cut out a patch section from that, can't find one. I guess I'll have to be creative. When the floor is done,down goes the new carpet.
 And if that's not enough work for right, my wife is tackling all new cushions, foam and fabric. She's bought the foam and the fabric and is hard at it.
 Well this is one old Clipper that will be relived. When I can get photos posted I will.

 P.K. :) 

Offline Toedtoes

  • Administrator
  • Seasoned Pro
  • *****
  • Posts: 511
    • Toedtoes Productions
Re: All kinds of cab work
« Reply #1 on: April 10, 2017, 01:36:37 AM »
Taking out the AC parts will open up the engine compartment nicely and eliminate any heat issues you may have had. It's so nice, I can feel the breeze coming through. It also makes it a lot easier to reach things in there.
'75 American Clipper Dodge 360 821F; ACOC #3754

Offline Clipper Joe

  • National Club Member
  • Seasoned Pro
  • *
  • Posts: 495
Re: All kinds of cab work
« Reply #2 on: April 14, 2017, 03:38:06 PM »
Hello PK,
Well Seems Like You Have A Project Ahead Of You, Good Luck.

Under My Cab Carpet & Mat Material, I Installed A Product Called Dynamat, One Box contains 36 Sq. Ft. It Is A Sound Deading & Reduces Road Noises &  Vibration. & Keeps Heat Down. Its A little Costly But Works Great. I Also Put A Better Padding Under Carpet Also. This Makes It Real Comfortable In Cab Area In Summer Cooler & Winter A Lot Warmer.

Also Used Special Heat Res. Foil Backed In Dog House, There Are Some Posts On Web Site. Note: I Found 2000 Degree Foil At Oriellys Auto Parts. Use Caution On What Stuff You Use They Can Catch On Fire & Burn Clipper.

On Heat Shields They Are Mounted Just Inside Of Cut Out & Mounted 3ea. 1/4" Tapping Screws.

Hopes This Helps, If You Have Any Question Please PM Me.

Joe   
1977 Dodge 440  Rear Kitchen
ACOC#3749

Offline Clipper Joe

  • National Club Member
  • Seasoned Pro
  • *
  • Posts: 495
Re: All kinds of cab work
« Reply #3 on: April 14, 2017, 03:48:39 PM »
Hi Toedtoes,

 What About Mentioning To Save All Your Old A/C Parts Removed Just In Case Next Owner Wants A/C Put Back On.

But It Has Worked Well On Your Clipper.

Joe
1977 Dodge 440  Rear Kitchen
ACOC#3749

Offline rvanarsdale

  • Rookie
  • *
  • Posts: 9
  • I Am Menelaus
    • Am I Menelaus
Re: All kinds of cab work
« Reply #4 on: April 20, 2017, 04:29:32 AM »
Wish I could find the time/money to do something similar to my a/c. I think it might work, shockingly, but I don't use it.
Good luck!
The whole problem with the world is that fools and fanatics are always so certain of themselves, and wiser people so full of doubts. - Bertrand Russell

Offline Howard Bullit Stubbs

  • Rookie
  • *
  • Posts: 8
Re: All kinds of cab work
« Reply #5 on: April 22, 2017, 10:17:20 AM »
 The idler pulley bracket with the pulley is mounted and the alternator belts are adjusted. I took photos. I'm adding a fresh air vent at the passengers feet. I removed the cover that blocks off the hole there and got another vent door that's at the drivers feet. We'll just mount it upside down on the passenger side and it will open up the same way as the drivers side. Then we'll trim the panel below the glove box so the passenger can reach down to the vent to open and close it.
 Those vents at your feet sure do let in lots of cool air. Seems like all the cars back in the sixties had them, remember when you opened one up on a cool summers night and just about froze!
 I have a question for you guys. Is there a photo posting link site that people find preferable, simple, works best for them? I'm better with hand/machine tools than I am with the computer. Thanks

Offline rvguy101

  • Rookie
  • *
  • Posts: 9
Re: All kinds of cab work
« Reply #6 on: April 23, 2017, 12:16:32 PM »
i left my ac stuff in,. i did add Heat Res, in the dog house,. i did add Padding, where i want more, or better,. & as for the photo posting link site,. try photobucket, it easy for me,.
77 dodge clipper, with 20,000 miles. & a 76 Holiday Rambler class c, with 100,000 miles,. & a 78 dodge clipper, with 100,000 miles on it,.